Quantcast
Channel: Applianceblog Repair Forums
Viewing all 58835 articles
Browse latest View live

SHE7PT55UC/07 Bosch dishwasher burning smell

$
0
0
My Bosch dishwasher has an acrid/electrical smell coming from the back of it. it has progressively gotten worse over the last few weeks. The dishwasher still runs and washes however I have stopped using it. When I open the cabinet beside it that has an opening to the back of the dishwasher, the smell is very pronounced so it leads me to believe its not likely the control board in the door. I pulled the dishwasher out and the smell is coming from the back inside the case.

I am looking for troubleshooting suggestions before I begin replacing parts like the Circulation pump or the control board. I have not yet pulled it out to take a closer look, not sure where to start. Any help / suggestions would be appreciated.

Thanks,
Kevin

FIXED WTW57ESVW1 Could fabric selector calls this?

$
0
0
Water runs in before the agitator starts when the fabric selector is on hand wash but on any other setting the agitator starts first. Also it's not spinning out correctly. What do I need to change to make this thing work right

KEBS207DBT8 Kitchenaid "too hot" door locked

$
0
0
Thank you for this incredible forum! Here is my problem and the troubleshooting I have done:

ran self-clean and oven had power failure - could not revive after cutting power and rebooting - no display at all and upper and lower doors were locked.
I tested the thermal fuse in the back and it was blown...I replaced the thermal fuse (WP9759242) - still no power to display
I replaced the in-line thermal fuse in the control unit behind display (WP4456654) - after rebooting the display came back on and registered error codes for door locked.
But now the display is lighting up but any button that I push will result in "too hot" error. Alternating with the error codes for door locked.

I did see a forum thread similar to this that suggested that the control unit was bad, but wanted to know if there is a way I can test this? Could it be that I just need to manually unlock the door from the back?

What do you recommend I do next?

Thank you!

Samsung DV52J8700GP gas dryer, heat shuts off after a few seconds

$
0
0
Ignitor glows and it flames up, but shuts off after a few seconds. If I take the high limit sensor out of the equation, it will stay on. Replaced sensor, no change. My thought is gas flow, so I changed out the gas valve, still no change. I feel like the flames are "licking" the high limit sensor and tripping it. Not sure what else to do except maybe replace the gas line? All sensors and coils check out on the multimeter... Am I missing something else?

Put a video on YouTube in case that helps any. https://youtu.be/G-9ZKT_pAEg

Thanks for any help! Been fighting it for a couple weeks now!

AWN432SP111TW01 Speed Queen washer stopped working mid-cycle

$
0
0
I have a Speed Queen washing machine model AWN432SP111TW01, serial 1110013649.

It's been working fine for years and we had never had any trouble with it, but today it stopped mid-cycle, and won't turn back on.

I tested another device in the same electrical socket and it worked fine. I ran an extension cord from an electrical socket in another room which was working fine and connected the washer to it, but still nothing.

I looked in the user guide troubleshooting section under "Won't Start". I have tried everything there. One of the suggestions there is to give it a few minutes for the motor overload protector to reset; I have given it hours.

The user guide does not mention a fuse in the washer.

I opened up the control panel area of the washer and looked for a fuse but did not find one. There was a sheet in there with a schematic. I scoured it for a fuse but it did not mention one.

I looked all over in there for anything that looked burned or otherwise damaged, or loose, etc. Everything looks as good as new and all connections seem tight.

Any suggestions on what I can try?

KUDE60HXSS5 No Blue LED while Washing

$
0
0
Hi - we have a KUDE60HXSS5. It is running well with one minor issue. On the front panel is a single LED. It is supposed to be blue when washing, red when drying and green when completed.

It no longer displays a blue light when washing.

Red when drying and green when complete still work.

I have tried shutting off the breaker to the dishwasher for a bit (5 - 10 mins) to see if that would reset anything. That did not make a difference.

I've also tried (I think) running a diagnostic cycle. I had seen elsewhere in this forum that if I pushed three buttons in the same order 3 times, it would run diagnostics. Indeed, I did that and all the buttons lit up, and I closed and it did something. I left it for a while and when I opened it, no lights on any of the buttons were on. So my guess would be that the diagnostics found nothing wrong?

Any ideas as to what would cause the blue light only on the front indicator not to light up?

Thanks so much,
Hilary

Maytag MVWX500XW1, cycle won't start

$
0
0
Hello, please help me figure this out.

My washer had stopped working in the middle of a cycle on Friday. My kid said they heard a thunk noise and I checked the washer. It had stopped at the spin cycle.

I ran diagnostics and got F7 E1. I just replaced the actuator today. I tried to run through calibration but it stopped calibrating. The lid lock light was blinking. Ran diagnostics again, still says F7 E1. I spun the drum, it spins freely and without resistance. The lid will lock but the light still blinks when I try to start a cycle. I tried going through the Drain and Spin cycle. It'll drain but it won't spin.

What else could I do? Thank you.

squeaks during wash cycle

$
0
0
Washer squeaks during agitation. Eventually, the agitator rises up a few inches, even after I hammered it back down. If I pull out the agitator from the machine and run the wash cycle, it doesn't squeak.

Oven stopped working: no heat, no gas smell, no errors

$
0
0
Hello all,

I was using my Magic Chef oven the other day for a little heat in the kitchen in the morning (don't worry, I don't run it for long like this; just long enough to take the chill off). It started warming up, then I noticed the smell of gas and it wasn't getting any hotter so I turned it off. A few minutes later I tried turning it on, it let me set the temperature, but the oven never warmed up. There's no smell of gas. There's also no error codes. It just sits at 350 or whatever temp I set it but nothing happens. No error codes are ever shown, it doesn't shut off, the preheat light stays on, and that's about it.

I've had the igniter go before but this has produced an error code the two times it died previously, the oven would beep, then turn off. I replaced it anyway but unfortunately the problem persists.

I'm not sure where to go from here. Does anyone have any suggestions? The range works fine by the way; it's only the oven that's broken.

Thanks

GFE29HSDASS Evap Motor and firmware?

$
0
0
Hello. I know I need to replace the evap. Motor in my GE fridge model number listed above. My question is if I will also need to update the firmware. The Fridge was manufactured in late 2013 with a serial number of TX516061. I know there is a service bulletin but I can not find it. Any help would be much appreciated.

How to take top off Maytag mvwb750wq0

$
0
0
How do I get the top off this washer ????

Top Load washer making LOUD bang bang bang noise in spin cycle

$
0
0
I read thru other threads on Amana washer noise. Could find nothing similar. This problem is a very loud bang bang bang noise (not "roaring noise)during spin. Transmission? (Splutch kit) Or springs

Kenmore Dishwasher "Complete" light blinks and no start... Help please!!

$
0
0
I have a Kenmore d-washer that the "COMPLETE" light will blink 4 times, pauses then blinks 4 more times. I shut the breaker off for 15 mins, turn on again and it does the same thing. I tried the heated dry/normal to start diagnostics and the complete light keeps blinking and none of the other buttons respond at all. Any help??

Washer continues to spin and won’t complete cycle

$
0
0
My washer continues to spin and won’t complete cycle. Will keep on spin cycle unless manually stopped.

CGR3740BDH Oven stopped working: no heat, no gas smell, no errors

$
0
0
Hello all,

I was using my Magic Chef oven the other day for a little heat in the kitchen in the morning (don't worry, I don't run it for long like this; just long enough to take the chill off). It started warming up, then I noticed the smell of gas and it wasn't getting any hotter so I turned it off. A few minutes later I tried turning it on, it let me set the temperature, but the oven never warmed up. There's no smell of gas. There's also no error codes. It just sits at 350 or whatever temp I set it but nothing happens. No error codes are ever shown, it doesn't shut off, the preheat light stays on, and that's about it.

I've had the igniter go before but this has produced an error code the two times it died previously, the oven would beep, then turn off. I replaced it anyway but unfortunately the problem persists.

I'm not sure where to go from here. Does anyone have any suggestions? The range works fine by the way; it's only the oven that's broken.

Thanks

How to take top off Maytag MVWB750WQ0

$
0
0
How do I get the top off this washer ????

GFWR4805F0MC Washer continues to spin and won’t complete cycle

$
0
0
My washer continues to spin and won’t complete cycle. Will keep on spin cycle unless manually stopped.

FFLE3911QW0 Washer turn on nothing got it to beep 3xs and then nothing

$
0
0
Age don't know- washer dryer combo-washer turn on nothing got it to beep 3xs and then nothing dryer works fine so iam hoping something simple.i did find a strand of 2 white and one black wire each end has a plug but don't see where it might plug into. It was laying loose in between dryer and washer

LFX25975ST/0 arm gets stuck - ice in gear

$
0
0
I've been strugging with this for a few months. The arm that detects a full ice bin gets stuck, not allowing the icemaker to cycle. I can trace this back to ice in the gear for the sensor arm. I can take it apart, remove a chunk of ice, and everything works great for about a month, but then I'm right back where I started. I see a tiny bit of ice accumulation on the gasket of the icemaker door. My temps are 38 and 0.

Any thoughts?

GE Model JTP56SD1SS convection fan seizes and heating element keeps heating

$
0
0
This a 17 year old oven. When using convection bake at 400 degrees, the fan and heating element turn on and both run until about 300 degrees. Then, convection fan seizes and heating element keeps heating. Sounds like fan motor is running, but blade is not turning. It stops heating at preset temp of 400 although temp in oven (used separate temp device) is only about 300. Non convection settings using bake and broil seem to work fine. Should I replace convection fan motor? What’s up?
Viewing all 58835 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>