Cabrio Dryer won't heat
Backstory: Dryer vent was clogged. Snaked and shopvacced. Guess: When it was clogged, something got too hot. Error code: F31 Jake, I saw that there was a repair mainual for the 6000 series of dryers...
View ArticleShorted refrigerator lights now LED display and ice/water dispenser do not work.
I have a Kitchenaid KSCS25INSS02 side by side refrigerator. The frige lights were not working, and I found the contacts at the bottom of the bulb sockets were bent. I thought I could be careful enough...
View ArticleQC test gives "nE" code.
I am testing this LG washer. I put it into QC mode, and it gives a "nE" code after a few seconds. It won't go any further. Other than that it appears to work during normal operation. I couldn't find...
View Articlemaytag 3000 error code f22 replaced door latch
Hi, read thread about error code f22. Replaced latch. Machine started and did 3/4 of a load and gave error code f22 again. Where should I start next? I've read some about a CCU...location? Thank you...
View ArticleWP 465 electric, oven only heats to 285
I'll set the temp to 400 or whatever then the digital display tells me 285 and that's as high as it gets. Problem has been intermittent but has become more constant to the point that I can't cook...
View ArticleDispenser will not dispense water / Ice works / No water from inlet valve
I have a Hotpoint HSS25GFTAWW. I removed the rear panel and disconnected the water side of the inlet valve. Pushing the water dispenser (light is on) causes the usual buzz that I would expect but no...
View ArticleDishwasher has no power
Hi I need help, I bought a brand new dishwasher, Frigidaire, and hooked up the black wire with the black wire for power and same thing with the white wire and then grounded the green but no power. I...
View ArticleKenmore HE2t - No Error Codes, Won't Spin Fast
Kenmore HE2t. Has always worked great. All of the sudden, it will not reach high spin speed during a cycle. Ran diagnostic test - no error codes. Drum did high spin like a champ during the diagnostics....
View Article80 Series model 110.64812200 push to start, timer, high heat?
The first issue that happened was the push to start button being *really* hard to push. The dryer functioned fine except for that issue. I filed it under "We're gonna have to replace that soon", and...
View ArticleRapidly blinking Normal Wash light
Tech sheet says this is caused by stuck or shorted key switch line, on control or keypad. Per Stuck Key Test, I disconnected the ribbon cable at P1, put things back together, turned on power, and the...
View ArticleCompressor replacement
I had my Frigidaire M#FFU20F9GW2 SWB83221321 Date-8/98 compressor lock up on me, I tried just to let it sit and reset, also installed a 3-n-1 still was not getting the compressor to start. I priced a...
View ArticleKenmore Model 70 will only final spin "Manually."
Hi. My Kenmore Model 70 Heavy Duty "Extra Capacity Plus" Quiet Pak Type III washing machine is 'missing' the final spin. It will go through the agitate and rinse cycles normally but 90% of the time it...
View ArticleClik here to view.
GSD1200T02 GE Potscrubber leaking from below
I have a leak near the drain valve. When valve is pulled down a lot more water comes out. Slow drip when off. Any idea where the water might be coming from and if a guy with no dishwasher repair...
View ArticleIce maker not filling with water
My Sub Zero 550 stopped making ice. When I jump the T and H the motor goes through the full cycle and the fingers stop at the 2:00 position. When I jump the V and L the water flows into the tray but...
View ArticleDryer connector meltdown
Last week my wife tells me, "there is a funny smell coming from the dryer and smoke, I think". A few seconds later, it is dead. I pulled the top off today. There are two connectors running from the...
View ArticleGE Oven won't shut off.
This GE model is "Slide - In" range/oven. I read a thread dated March 16, 2011 where someone with a GE Oven but with different model had the same problem where the oven would not shut off when we press...
View ArticleStuck blower wheel
My kenmore he3 stopped running a few weeks ago and I have tested everything and it came down to the motor. I now have a new motor and am trying to take the old one out! The problem is that the blower...
View Articleagitator removal
Does anyone have a special trick to remove a stubborn agitator? I have removed the stud that secures it to the top of the tranny shaft but it will not budge. I have also put a ratchet strap under the...
View ArticleIntermittent no spin
Hello. After searching through old posts, it looks like No Spin is a pretty common issue. I tried to read old posts for help, but none of them seemed to match my issue. The washer seems to work fine in...
View ArticleClik here to view.
Model 70 Washer Agitator removal... no 7/16" bolt!!!!
Okay, so my "Agitator Dogs" are worn out, i.e. the agitator is loose and won't agitate. I read the threads, looked at the cool videos on Repair Clinic and ordered the parts. It will take a few days to...
View Article